This great article which follows about Tools You Need to Install a New Bathtub is unquestionably compelling. You should investigate it.
Installing a tub isn't specifically rocket science, but it does need strong plumbing, carpentry, and in some cases, tiling skills. Changing an old bath tub with a brand-new one is also a moderately challenging job. If the old bathtub is conveniently obtainable, the project can move rapidly; if you need to open up a wall surface to get rid of the old tub and position the brand-new tub, the job is a lot harder. In either case, the project is within a house handyman's skills, although you will certainly require an assistant to vacate the old tub and set in the new one. Make certain you have actually certified on your own for the work and also fit attempting it. Rather than hiring a professional to take over a halfway-completed job, it is much better to think about utilizing one before you begin. Possibilities are you may need a professional plumber to make tube connections.
This article will help you install a new bathtub in your bathroom if you have already bought a new tub as well as do not need to change the setup of your previous water system pipes.
Your tools and product list ought to comprise the following:
Preparing for the Installment
To start with, the supporting frame provided with the bathroom should be fitted (if called for) according to the maker's directions. Next, fit the faucets or mixer to the tub. When fitting the faucet block, it is essential to make sure that if the faucet includes a plastic washer, it is fitted in between the bath and also the faucets. On a plastic bath, it is additionally practical to fit a supporting plate under the faucets unit to stop stress on the bathtub.
Fit the versatile tap adapters to the bottom of the two faucets utilizing 2 nuts and olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet with the hole in the bath. Make use of the nut provided by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make sure you utilize all of the provided washers.
Attach the catch to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom need to now be ready to be suited its last position.
Removing Old Taps
If you require to change old faucets with brand-new ones as a part of your installation, after that the first thing you need to do is detach the water. After doing so, turn on the taps to drain pipes any water staying in the system. The procedure of removing the existing taps can be fairly problematic because of the limited accessibility that is frequently the instance.
Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipelines to the faucets. Have a cloth ready for the staying water that will certainly come from the pipes. When the supply pipelines have actually been removed, use the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will need to quit the solitary faucets from turning during this process. When the faucets have actually been removed, the holes in the bath/basin will have to be cleaned up of any kind of old securing substance.
Before proceeding to fit the new faucets, contrast the pipe connections on the old taps to the brand-new faucets. If the old taps are longer than the new taps, then a shank adapter is needed for the brand-new faucets to fit.
Mounting the Bath tub
Using the two wooden boards under its feet, place the tub in the needed setting. The wood boards are practical in equally spreading out the weight of the bath tub over the area of the boards instead of concentrating all the weight onto 4 tiny factors.
The following objective is to make sure that the bathtub is leveled all round. This can be accomplished by inspecting the level and also readjusting the feet on the bathtub until the spirit level checks out level.
To set up faucets, fit all-time low of the outermost adaptable tap connector to the appropriate supply pipe by making a compression join; then do the exact same for the various other faucet.
Turn on the water and also examine all joints and also brand-new pipework for leakages and also tighten them if essential. Fill the bathtub and also check the overflow outlet and the normal outlet for leakages.
Ultimately, take care of the bathroom paneling as explained in the manufacturer's instruction manual. Tiling and also securing around the tub ought to wait until the bath tub has actually been utilized a minimum of once as this will certainly settle it into its final position.
Suitable New Touches
If the tails of the brand-new faucets are plastic, then you will need a plastic connector to stop damages to the thread. One end of the connector fits on the plastic tail of the faucet as well as the other end provides a link to the existing supply pipes.
If you require to fit a monobloc, after that you will require lowering couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next, place the faucet in the installing hole in the bath/basin guaranteeing that the washers remain in location in between the faucet as well as the sink. Secure the faucet in place with the manufacturer supplied backnut. Once the faucet is securely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with regular tap adapters. The former type must be connected to the tap finishes first, tightening just by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bath tub
In the area where the bathroom satisfies the floor tile, it is required to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to fracture a rigid seal, creating the water to penetrate the wall surface in between the bath and also the tiling, resulting in difficulties with moisture and also possible leaks to the ceiling listed below.
You can choose from a variety of coloured sealers to assimilate your fixtures as well as installations. They are marketed in tubes and cartridges, as well as can securing gaps approximately a width of 3mm (1/8 inch). If you have a larger void to fill, you can load it with spins of soaked newspaper or soft rope. Bear in mind to always fill up the bath tub with water before sealing, to permit the movement experienced when the tub remains in usage. The sealant can split rather early if you do not take into consideration this activity prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise conveniently readily available on the market. It is recommended to fit the ceramic tiles making use of waterproof or waterproof adhesive as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We hope you liked our section on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thanks so much for taking the time to browse our piece of content. Enjoyed our blog posting? Please share it. Let others locate it. We enjoy reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Booking Page